Patton250 Posted August 5, 2019 Share Posted August 5, 2019 (edited) 6 hours ago, mrelwood said: I’ll do better! $900, + reasonable shipping costs of course! . Edited August 5, 2019 by Patton250 Quote Link to comment Share on other sites More sharing options...
Gaz Bon Posted August 5, 2019 Share Posted August 5, 2019 And now it's a For Sale Thread 🤐☹🤑🤑🤑 1 Quote Link to comment Share on other sites More sharing options...
Unventor Posted August 5, 2019 Share Posted August 5, 2019 (edited) 4 minutes ago, Gaz Bon said: And now it's a For Sale Thread 🤐☹🤑🤑🤑 Yep, I knew KS wheels are versatile, but this thread ... gives a new meaning to "jack of all trades".... Edited August 5, 2019 by Unventor Quote Link to comment Share on other sites More sharing options...
LucasD Posted August 5, 2019 Share Posted August 5, 2019 7 hours ago, chrisjunlee said: Hmm, I see you’re unfamiliar with BMS. You do you. For everyone else: the BMS is what handles charging and balancing. Both Kingsong inlets are connected in parallel and thus, to the same BMS units. I’m not even going to address the “high risk” “battery imbalance” “face plant” argument. You’ve somehow misplaced the conclusion to a completely different root cause (people disconnecting their charger after the light goes green). Friendly advice is fine, but be aware of when you’re spreading nonsense and be prepared to be called out for it. BMS maybe a BS reason, but connecting two chargers is not a good idea. Unless they are perfect sources (balance), plus you are introducing ground loop. From Quora Balancing power output is always a unknown path to problems. This is the same as having a power supply with two or more power transistors running in parallel, you need to balance the power and current through them. If you are talking about a DC 12V adapter or so, dealing with 1 or 2A of current each, I would suggest to not correct their wires exactly in parallel. Just use a low resistance resistor in series with each one before you connect the wires together. I would say 0.1 (zero point one) ohm, 1 Watt resistor in each adapter output, then correct the other side of the resistors together (parallel), it would be a better setup then just “parallel” the outputs. The resistors will create a kind of reference of each output for itself, instead of the voltage of one interfere with the control feedback of the other. It works better. Being low value (0.1) it will not interfere with the output voltage. 2 Quote Link to comment Share on other sites More sharing options...
Patton250 Posted August 5, 2019 Share Posted August 5, 2019 7 minutes ago, Gaz Bon said: And now it's a For Sale Thread 🤐☹🤑🤑🤑 Deleted Quote Link to comment Share on other sites More sharing options...
ir_fuel Posted August 5, 2019 Share Posted August 5, 2019 11 minutes ago, LucasD said: BMS maybe a BS reason, but connecting two chargers is not a good idea. Unless they are perfect sources (balance), plus you are introducing ground loop. So why does King Song provide us with 2 charging ports. Also plenty of people have already dual charged their euc's. How many issues arised from this? 11 minutes ago, LucasD said: From Quora Balancing power output is always a unknown path to problems. This is the same as having a power supply with two or more power transistors running in parallel, you need to balance the power and current through them. If you are talking about a DC 12V adapter or so, dealing with 1 or 2A of current each, I would suggest to not correct their wires exactly in parallel. Just use a low resistance resistor in series with each one before you connect the wires together. Who says this isn't the case inside the wheel? Also, who wrote this answer. Anyone can be an "authority" on Quora, and some people seem to make a full time job out of it. 2 Quote Link to comment Share on other sites More sharing options...
erk1024 Posted August 5, 2019 Share Posted August 5, 2019 (edited) 14 hours ago, Patton250 said: I think it would be very cool to watch your speed from your wrist. Darkness Bot works with an Apple Watch. I've been using it for a few weeks now. It will show things like speed, battery percentage, current ... Edited August 5, 2019 by erk1024 1 1 Quote Link to comment Share on other sites More sharing options...
Chriull Posted August 5, 2019 Share Posted August 5, 2019 1 hour ago, LucasD said: BMS maybe a BS reason, but connecting two chargers is not a good idea. Unless they are perfect sources (balance), plus you are introducing ground loop. From Quora Balancing power output is always a unknown path to problems. This is the same as having a power supply with two or more power transistors running in parallel, you need to balance the power and current through them. If you are talking about a DC 12V adapter or so, dealing with 1 or 2A of current each, I would suggest to not correct their wires exactly in parallel. ... That is true for constant voltage supplies. They cannot be put in parallel (just with some resistor inbetween ..) But li ion chargers work as constant current supplies (at least while the first phase). There paralleling is no problem. Probs could start at the CV phase, since both have different max voltages - so one charger would have to sink the current of the other. Which ?maybe some? swithched supplies do not like? But since this paralleling is done since years with the charge doctor nothing happened it seems do be no prob? 2 Quote Link to comment Share on other sites More sharing options...
LucasD Posted August 5, 2019 Share Posted August 5, 2019 Because all EUC manufactures are very low in electronics (look at multiple post). E.g. Live charge in ports of EUC instead of using diod to limit current in other direction, etc... How many people ride like idiots with straight legs? It may be fine for few people, until some imbalance either brick charger or most likely burn something on your board... P.S> Have you even heard of ground loops? And have any idea of polarity in electric sockets... 1 Quote Link to comment Share on other sites More sharing options...
LucasD Posted August 5, 2019 Share Posted August 5, 2019 2 minutes ago, Chriull said: That is true for constant voltage supplies. They cannot be put in parallel (just with some resistor inbetween ..) But li ion chargers work as constant current supplies (at least while the first phase). There paralleling is no problem. Probs could start at the CV phase, since both have different max voltages - so one charger would have to sink the current of the other. Which ?maybe some? swithched supplies do not like? But since this paralleling is done since years with the charge doctor nothing happened it seems do be no prob? Would not be suprised that charge doctor put some balancing circuits and if not the most likely point of failure would be charge doctor... Quote Link to comment Share on other sites More sharing options...
ir_fuel Posted August 5, 2019 Share Posted August 5, 2019 Just now, Chriull said: But li ion chargers work as constant current supplies (at least while the first phase). There paralleling is no problem. Probs could start at the CV phase, since both have different max voltages - so one charger would have to sink the current of the other. Which ?maybe some? swithched supplies do not like? But are they li ion chargers? AFAIK they just output X volts and that's it. Quote Link to comment Share on other sites More sharing options...
erk1024 Posted August 5, 2019 Share Posted August 5, 2019 6 hours ago, Tadas said: 2.5 hours for my KS18XL to balance just 1% imbalance How did you figure that out? Is there a way to display the battery voltages? I know the OneWheel did this for a while before they removed the feature as it caused too many support calls (presumably). Quote Link to comment Share on other sites More sharing options...
Chriull Posted August 5, 2019 Share Posted August 5, 2019 4 minutes ago, LucasD said: P.S> Have you even heard of ground loops? All the used chargers for EUCs are galvanicly isolated and have no grounding ("earth potential") for the output... But wouldn't be too surprised if once a batch comes differently... But still would not matter if they put ground on the same output (logically ground/minus) 2 minutes ago, LucasD said: Would not be suprised that charge doctor put some balancing circuits and if not the most likely point of failure would be charge doctor... Would be confident that @hobby16 put some safeguards to his CD, if necessary. Quote Link to comment Share on other sites More sharing options...
Chriull Posted August 5, 2019 Share Posted August 5, 2019 6 minutes ago, ir_fuel said: But are they li ion chargers? AFAIK they just output X volts and that's it. The chargers supplied with the EUCs are all li ion chargers - start with cc phase and finish off with the cv phase. 1 Quote Link to comment Share on other sites More sharing options...
ir_fuel Posted August 5, 2019 Share Posted August 5, 2019 1 minute ago, Chriull said: The chargers supplied with the EUCs are all li ion chargers - start with cc phase and finish off with the cv phase. So what you are saying is that I can't just take the plug, cut the cord and connect it to some random device that outputs a constant 84V to charge my wheel? So it's not the electronics inside the wheel that do the CV/CC switching? Quote Link to comment Share on other sites More sharing options...
Chriull Posted August 5, 2019 Share Posted August 5, 2019 22 minutes ago, ir_fuel said: So what you are saying is that I can't just take the plug, cut the cord and connect it to some random device that outputs a constant 84V to charge my wheel? So it's not the electronics inside the wheel that do the CV/CC switching? Exactly. Just if your 84V supply has some current liming it could work out. But if the supply is too strong (delivers too much current) it'l blow up the cells. ... Or itself if it has no overpower/current shutoff... Quote Link to comment Share on other sites More sharing options...
ir_fuel Posted August 5, 2019 Share Posted August 5, 2019 33 minutes ago, Chriull said: Exactly. Just if your 84V supply has some current liming it could work out. Yes of course. You shouldn't connect a 20A 84V source to it But I see what you mean. In that case I wonder how CV/CC is handled if you connect 2 different types of chargers, each delivering different amps. I would make sense that the only safe solution in that case (and even then ...) would be to connect 2 identical chargers. 1 Quote Link to comment Share on other sites More sharing options...
Popular Post Rehab1 Posted August 5, 2019 Popular Post Share Posted August 5, 2019 Awesome!!!! The KS16X 5A charger just arrived from Ewheels! Thanks @Jason McNeil! 6 3 Quote Link to comment Share on other sites More sharing options...
Popular Post BleepBloopBlop Posted August 5, 2019 Popular Post Share Posted August 5, 2019 (edited) I don't get why people are saying this wheel is boring? Are you riding it slow? I'm riding mine like my city motorcycle in the road everywhere I go as long as the speed limit is 30mph and under. I'm thankful its stable enough to comfortably do this in a sustained manner. Also it has plenty of power to swiftly accelerate up to speed as well as climb every hill I've put it up against. I'm going to hit 400 miles of riding today on my 16X and its been an amazing first week! Edited August 5, 2019 by BleepBloopBlop 6 3 Quote Link to comment Share on other sites More sharing options...
Unventor Posted August 5, 2019 Share Posted August 5, 2019 40 minutes ago, Rehab1 said: Awesome!!!! The KS16X 5A charger just arrived from Ewheels! Thanks @Jason McNeil! But have unwrapped the wheel from its garage camouflage and ridding it so far? 1 Quote Link to comment Share on other sites More sharing options...
Popular Post Tadas Posted August 5, 2019 Popular Post Share Posted August 5, 2019 3 hours ago, erk1024 said: How did you figure that out? Is there a way to display the battery voltages? I know the OneWheel did this for a while before they removed the feature as it caused too many support calls (presumably). 42 mA balancing current, 3 cells in parallel each 3500 mAh, so that's 10500 mAh. 1% imbalance would be 105 mAh and take 2.5 hours to balance. 2 3 Quote Link to comment Share on other sites More sharing options...
chrisjunlee Posted August 5, 2019 Share Posted August 5, 2019 (edited) 14 minutes ago, BleepBloopBlop said: I don't get why people are saying this wheel is boring? Are you riding it slow? I'm riding mine like my city motorcycle in the road everywhere I go as long as the speed limit is 30mph and under. I'm thankful its stable enough to comfortably do this in a sustained manner. Also it has plenty of power to swiftly accelerate up to speed as well as climb every hill I've put it up against. I'm going to hit 400 miles of riding today on my 16X and its been an amazing first week! I would like to see a video of you climbing a 20-25% hill from a dead stop. It's an exhausting experience for me compared to mten3 or MCM5. Put it another way: on the mten3 and MCM5, you can carve uphill with ease. On the 16X, at least for me, it feels like I'm crawling when I'm literally on my tippy toes (nothing else touching the pedal besides the balls of my feet, and my legs gripping the wheel for support as I michael jackson lean forward). Edited August 5, 2019 by chrisjunlee Quote Link to comment Share on other sites More sharing options...
Rehab1 Posted August 5, 2019 Share Posted August 5, 2019 3 minutes ago, Unventor said: But have unwrapped the wheel from its garage camouflage and ridding it so far? Yes I had it out to the park twice yesterday thanks to my mother-in-law keeping my wife busy. I love this wheel. I’ve experienced the same wobble attitude other members speak about occurring around the 27 mph (43kph) mark. I just rapidly decelerate to diminish it. Cruising through the wooded, bumpy trails I experienced was effortless. I actually prefer the handling over the Z10. I did shoot some off road video but unfortunately finding the time to process it without prying eyes looking over my shoulder is difficult. Any ETA on your 16X arriving? 3 Quote Link to comment Share on other sites More sharing options...
ir_fuel Posted August 5, 2019 Share Posted August 5, 2019 8 minutes ago, chrisjunlee said: ut it another way: on the mten3 and MCM5, you can carve uphill with ease. On the 16X, at least for me, it feels like I'm crawling when I'm literally on my tippy toes (nothing else touching the pedal besides the balls of my feet, and my legs gripping the wheel for support as I michael jackson lean forward). Will be exactly the same with any other wheel, except for the MCM5 and the Mten3. 1 Quote Link to comment Share on other sites More sharing options...
ir_fuel Posted August 5, 2019 Share Posted August 5, 2019 1 minute ago, Rehab1 said: I’ve experienced the same wobble attitude other members speak about occurring around the 27 mph (43kph) mark. I just rapidly decelerate to diminish it. Cruising through the wooded, bumpy trails I experienced was effortless. I actually prefer the handling over the Z10. Same here at the moment. On paved roads I grab the Z10. For the trails I take the KS16X. Never taken the Z10 off road BTW. On trails you don't hit those high speeds. The fastest I went was 30kmh off road. That's fast enough 3 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.