Ben Kim Posted April 27, 2023 Share Posted April 27, 2023 @Seba are you actively maintaining the repository of custom firmwares in @Freestylerabsence? Might be buying a new Begode wheel soon and would like to have this available on it. Quote Link to comment Share on other sites More sharing options...
RaulR Posted April 28, 2023 Share Posted April 28, 2023 Good night. Would there be the possibility of forcing the installation of the cfw to begode ex20s without using the "euc world" application? It's just that I can't get it with the application, I've tried every possible way and there's no way to update it with either OFW or with CFW... And the update doesn't work with the official begode app either. I have commented on it some other time, but the update process works perfectly, it ends at 100%, but it has not really been updated because, when connecting to euc again, it continues to indicate the original ofw version instead of the cfw version... @Seba @Freestyler any other brute force option? 😂 A lot of thanks for your help and work. Quote Link to comment Share on other sites More sharing options...
Lefteris Posted April 29, 2023 Share Posted April 29, 2023 On 4/6/2023 at 7:02 PM, Seba said: but for now Bill is apparently gone (last visited February 18) and no one knows when or if he'll be back again Bill had an accident in February.. He wasn't able to walk for at least 2+ months since.. It was bad.. 10 Quote Link to comment Share on other sites More sharing options...
Mike Sacristan Posted April 29, 2023 Share Posted April 29, 2023 13 hours ago, RaulR said: Good night. Would there be the possibility of forcing the installation of the cfw to begode ex20s without using the "euc world" application? It's just that I can't get it with the application, I've tried every possible way and there's no way to update it with either OFW or with CFW... And the update doesn't work with the official begode app either. I have commented on it some other time, but the update process works perfectly, it ends at 100%, but it has not really been updated because, when connecting to euc again, it continues to indicate the original ofw version instead of the cfw version... @Seba @Freestyler any other brute force option? 😂 A lot of thanks for your help and work. Install the Custom Firmware again with EUC World. Use EUC Dash to set dynamic tiltback.https://freestyl3r.github.io/euc-dash/begode.html Verify dynamic tiltback by lifting the wheel with the light on. It should tilt back and strobe. Not all modified versions of the firmware have the CF prefix so they will not be detected by EUC World or Darknessbot. 3 Quote Link to comment Share on other sites More sharing options...
Mantraguy Posted April 29, 2023 Share Posted April 29, 2023 I successfully flashed the custom firmware on my EX20S yesterday and it appears to work well, although I haven't really tested it much yet. I tend to like riding with my headlight flashing for visibility, but obviously this is not possible with dynamic tiltback enabled since it uses the strobe mode to indicate that tiltback is active. I wonder if this could be made into a selectable option in EUC world, so we can have both dynamic tiltback enabled but still use a strobing light during normal riding. To me, that would be perfect. :-) 1 Quote Link to comment Share on other sites More sharing options...
Lefteris Posted April 29, 2023 Share Posted April 29, 2023 29 minutes ago, Mantraguy said: [...] I wonder if this could be made into a selectable option in EUC world, so we can have both [...] While using CF you can't have strobe. If you want strobe switch back to stock Firmware! 😉 Quote Link to comment Share on other sites More sharing options...
Cerbera Posted April 29, 2023 Share Posted April 29, 2023 I'm still not sure the flashing headlight during tiltback is a good idea. In the day I'm surprised anyone notices, and at night you want a headlight that remains on regardless don't you ?! 1 1 Quote Link to comment Share on other sites More sharing options...
Rawnei Posted April 29, 2023 Share Posted April 29, 2023 3 hours ago, Cerbera said: I'm still not sure the flashing headlight during tiltback is a good idea. In the day I'm surprised anyone notices, and at night you want a headlight that remains on regardless don't you ?! It only flashes the headlight if it's already turned on, I think it's a great visual indicator at night. Quote Link to comment Share on other sites More sharing options...
Damarafaka Posted April 29, 2023 Share Posted April 29, 2023 17 hours ago, Lefteris said: Bill had an accident in February.. Hope Bill can recover completely, wish him all the best! 1 Quote Link to comment Share on other sites More sharing options...
Lefteris Posted April 30, 2023 Share Posted April 30, 2023 12 hours ago, Damarafaka said: Hope Bill can recover completely, wish him all the best! It's been hard for him psychically and mentally .. I can't see him returning.. at least any time soon.. 4 Quote Link to comment Share on other sites More sharing options...
Bizra6ot Posted May 1, 2023 Share Posted May 1, 2023 @Freestyler wishing you a speedy and full recovery mate get well soon! Quote Link to comment Share on other sites More sharing options...
bracky72 Posted May 1, 2023 Share Posted May 1, 2023 Yes that’s terrible news. I hope he heals up and can put it behind him. Quote Link to comment Share on other sites More sharing options...
taiguy Posted May 1, 2023 Share Posted May 1, 2023 Took my eWheels batch 2 Master out for a quick errand today. It's running Freestyler's custom firmware. Going down my street at maybe 20mph (32 kph) and I heard two beeps. Turned the corner and two more beeps. I hopped off to see my wheel do a gradual but steep tiltback. Turned the wheel off and then back on and crossed the street. Within half a minute heard the beeps again. I slowed down while it continued to give me the double beeps. The pedals tilted way back as I was already off the wheel. This is new behavior to me. I've got maybe 500 miles (800 km) on the wheel and have never seen it do this. Is this part of the CF firmware? Is this a different issue to troubleshoot? I rode a bit more and didn't have the issue come up again while out (total of 6 miles). Does the CF firmware tiltback on over voltage condition? Both instances were right after taking the wheel off the charger. Maybe braking pushed the voltage up a bit too much. Quote Link to comment Share on other sites More sharing options...
mrelwood Posted May 1, 2023 Share Posted May 1, 2023 (edited) 37 minutes ago, taiguy said: right after taking the wheel off the charger. Maybe braking pushed the voltage up a bit too much. That is definitely the most plausible reason. Next time (anything like) it happens, check the voltage. Edited May 1, 2023 by mrelwood Quote Link to comment Share on other sites More sharing options...
Bizra6ot Posted May 1, 2023 Share Posted May 1, 2023 1 hour ago, taiguy said: Took my eWheels batch 2 Master out for a quick errand today. It's running Freestyler's custom firmware. Going down my street at maybe 20mph (32 kph) and I heard two beeps. Turned the corner and two more beeps. I hopped off to see my wheel do a gradual but steep tiltback. Turned the wheel off and then back on and crossed the street. Within half a minute heard the beeps again. I slowed down while it continued to give me the double beeps. The pedals tilted way back as I was already off the wheel. This is new behavior to me. I've got maybe 500 miles (800 km) on the wheel and have never seen it do this. Is this part of the CF firmware? Is this a different issue to troubleshoot? I rode a bit more and didn't have the issue come up again while out (total of 6 miles). Does the CF firmware tiltback on over voltage condition? Both instances were right after taking the wheel off the charger. Maybe braking pushed the voltage up a bit too much. Over voltage is 3 beeps 2 beeps is either low voltage or overheat if they are like 2 seconds apart, or hall effect sensor problem if they are very close with no downtime like beepbeep..beepbeep Quote Link to comment Share on other sites More sharing options...
taiguy Posted May 1, 2023 Share Posted May 1, 2023 18 minutes ago, Bizra6ot said: Over voltage is 3 beeps 2 beeps is either low voltage or overheat if they are like 2 seconds apart, or hall effect sensor problem if they are very close with no downtime like beepbeep..beepbeep Is this documented anywhere? I put the wheel back on the charger when I got back. Took it off and opened the Begode app to check voltage. It keeps switching between 134V and 129.5V every second. Temp switches between 25.6 and 34.4 as well Quote Link to comment Share on other sites More sharing options...
RagingGrandpa Posted May 1, 2023 Share Posted May 1, 2023 6 minutes ago, taiguy said: Is this documented anywhere? Quote https://forum.electricunicycle.org/topic/8773-gotway-beep-code/?do=findComment&comment=128743 From Jane Mo: first speed alarm, 2 beeps per second second speed alarm, 3 beeps per second third speed alarm, 4 beeps per second 80% power alarm, 5 beeps per second(continuously non-stop beeping without pause) less than 7.2km/h, low voltage,1 beep every 2 seconds less than 14.4km/h, low voltage, 2 beeps every 2 seconds more than 14.4km/h, low voltage, 3 beeps every 2 seconds hall sensor defect, 2 beeps every 1/2 seconds PCB high temperature alarm, 2 short beep 2 seconds, tilt back to get rider off the EUC, tilting back and forward after stopped extreme low voltage power on,1 beep 1 second,totally 5 beep fall down,1 beep 1 second, total of 5 beeps over voltage, 3 short beep 2 second, tilt back when riding downhill 2 Quote Link to comment Share on other sites More sharing options...
taiguy Posted May 1, 2023 Share Posted May 1, 2023 2 minutes ago, RagingGrandpa said: thanks! sounds like case 12 might be the closest match then. Quote Link to comment Share on other sites More sharing options...
Bizra6ot Posted May 1, 2023 Share Posted May 1, 2023 (edited) They are the same on all Gotway/begode you can find the beeps chart on each datasheet or user manual Here on the 4th picture of the user's manual https://voltride.com/wp-content/uploads/2022/09/Begode-Master-V1.0-ENG-EST.pdf Edited May 11, 2023 by Bizra6ot typo Quote Link to comment Share on other sites More sharing options...
b1oki Posted May 9, 2023 Share Posted May 9, 2023 On 4/29/2023 at 9:03 PM, Mantraguy said: I wonder if this could be made into a selectable option in EUC world I agree, it was good to be able to choose this option. Also, the option on which PWM to Tiltback, now this is happening in the area of 77-80%. On 4/29/2023 at 9:34 PM, Lefteris said: While using CF you can't have strobe. If you want strobe switch back to stock Firmware! 😉 If anybody want strobe on Freestyl3r firmware, switch alert mode to one of default variants. Strobe don't turn on manually only with fourth alert mode. On 4/29/2023 at 9:48 PM, Cerbera said: at night you want a headlight ?! I'm use Mateminco MT04 flashlight for night rides. So I don't see strobe at 79% pwm because lamp of wheel is dim. 2 Quote Link to comment Share on other sites More sharing options...
evgesnev Posted May 18, 2023 Share Posted May 18, 2023 Hi, could you make please custom firmware for my begode rs hs 134 volts? If you need original firmware just contact me. Quote Link to comment Share on other sites More sharing options...
Lefteris Posted May 18, 2023 Share Posted May 18, 2023 2 hours ago, evgesnev said: Hi, could you make please custom firmware for my begode rs hs 134 volts? If you need original firmware just contact me. As per previous posts, @Freestyler won't be able to work with firmware files after his terrible accident. 4 Quote Link to comment Share on other sites More sharing options...
Popular Post Seba Posted May 18, 2023 Popular Post Share Posted May 18, 2023 On 4/27/2023 at 11:07 PM, Ben Kim said: @Seba are you actively maintaining the repository of custom firmwares in @Freestylerabsence? Might be buying a new Begode wheel soon and would like to have this available on it. Yes, I maintain repository of all custom firmwares that has been provided by @Freestyler. So while we shouldn't expect any new CFs (I still hope that Bill will recover and get back to us), already created firmware images are secured on EUC World server and available to EUC World users. 3 1 2 Quote Link to comment Share on other sites More sharing options...
ursi Posted May 24, 2023 Share Posted May 24, 2023 Anyone have this set up on a Hero? It seems the firmware breaks the headlight - I can't force it to turn off. It also doesn't strobe when hitting the beeps. I haven't gone fast enough to feel the tiltback yet (82% wasn't enough I guess, and I'm not very comfortable riding the final beeps) but when freespinning I do feel a jolt some time after 80%. Quote Link to comment Share on other sites More sharing options...
Cyph Posted May 24, 2023 Share Posted May 24, 2023 13 hours ago, ursi said: Anyone have this set up on a Hero? It seems the firmware breaks the headlight - I can't force it to turn off. It also doesn't strobe when hitting the beeps. I haven't gone fast enough to feel the tiltback yet (82% wasn't enough I guess, and I'm not very comfortable riding the final beeps) but when freespinning I do feel a jolt some time after 80%. You can test it out by setting 50% then ride the beep. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.