Planemo Posted August 23, 2023 Share Posted August 23, 2023 On 8/3/2023 at 5:28 PM, Kekafuch said: The rocker adjustment is the pedal angle forward / backwards. 4 being neutral. <4 being tilt forward and >4 tilt backwards. Angle Compensation will tilt the pedals up when you do a tight turn. This doesn't appear to be happening for me. 9 provides a level pedal (which I usually run), anything less tilts the pedals forwards Quote Link to comment Share on other sites More sharing options...
Aztek Posted October 27, 2023 Share Posted October 27, 2023 (edited) As I see now power alarm and tilt back at set % are available in the begode app, does this mean we can now flash the official firmware and have the pwm % tilt back (begode master)? Does anyone have experience? Edited October 27, 2023 by Aztek Quote Link to comment Share on other sites More sharing options...
Planemo Posted October 27, 2023 Share Posted October 27, 2023 On 8/23/2023 at 6:52 AM, Planemo said: This doesn't appear to be happening for me. 9 provides a level pedal (which I usually run), anything less tilts the pedals forwards I had a similar issue with my EX30 when I bought it (secondhand). The wheel had a couple of degrees forward tilt when on setting 4. I could change the setting in the app to make the pedals level but whenever I restarted the wheel it went back to how it was before - foward tilt at setting 4. I recalibrated the wheel and it has been fine since - level pedals at setting 4. I guess it should be level at setting 5 but I forgot to change it to 5 before I recalibrated.... Quote Link to comment Share on other sites More sharing options...
CrabChampion Posted October 27, 2023 Share Posted October 27, 2023 6 hours ago, Aztek said: does this mean we can now flash the official firmware and have the pwm % tilt back (begode master)? Yes it is available on the master v2 and above. I am not sure if the v1 and v1.5 master have the firmware update Quote Link to comment Share on other sites More sharing options...
nijaba Posted October 27, 2023 Share Posted October 27, 2023 14 hours ago, Aztek said: As I see now power alarm and tilt back at set % are available in the begode app, does this mean we can now flash the official firmware and have the pwm % tilt back (begode master)? Does anyone have experience? Been using it and quite happy with it on my v2. Quote Link to comment Share on other sites More sharing options...
Aztek Posted October 28, 2023 Share Posted October 28, 2023 15 hours ago, Cobaltsaber said: am not sure if the v1 and v1.5 master have the firmware update The app does not discriminate the master version. The firmware itself is not marked for specific version neither. I.e. flashing it seems the usual risky affair. Of course begode do not give any real info and the few words are in cryptic broken English... Since I have the freestyl3r's fw installed.and working properly, it is not a wise move to risk with the bg new fw having little to none info on what it does and how it does it. Quote Link to comment Share on other sites More sharing options...
RolluS Posted November 1, 2023 Share Posted November 1, 2023 (edited) On 10/27/2023 at 11:13 AM, Aztek said: As I see now power alarm and tilt back at set % are available in the begode app, does this mean we can now flash the official firmware and have the pwm % tilt back (begode master)? Does anyone have experience? Hi, I did it on my T4 V1: Now I have a nice brick: Auxiliaries (lights, beep) are working, no balancing, Begode app shows "MOS1 error", EUC World does not connect. @Seba please, would it be possible to set/give a proxy so I can flash @Freestyler firmware back using Begode App? Édit: no need for a proxy, I managed to downgrade with an older version of Begode App and the"start into bootloader" trick. Edited November 1, 2023 by RolluS Progress update 1 Quote Link to comment Share on other sites More sharing options...
RolluS Posted November 1, 2023 Share Posted November 1, 2023 (edited) Update: Now I'm back to GW1612104 (downgraded with older app version, and setting wheel into bootloader move with power+clicking lift).@Seba, EUC World does not detect this state. Now it's stuck in transportation mode. Usual lift+5*power does not work Playing with versions: - GW1612106 states a MOSFET error and screen/lights misfunction. I claimed for warranty with screen capture and videos. - GW1612104 works but stuck in transportation mode. I cannot believe I fried main board (mother board or MOSFET board) with just a firmware update Edited November 1, 2023 by RolluS 1 Quote Link to comment Share on other sites More sharing options...
Seba Posted November 2, 2023 Share Posted November 2, 2023 20 hours ago, RolluS said: Auxiliaries (lights, beep) are working, no balancing, Begode app shows "MOS1 error", EUC World does not connect. 13 hours ago, RolluS said: @Seba, EUC World does not detect this state. Well, it might be that this "project" firmware has different communication protocol. Also, doesn't rely on Begode app showing "MOS1 error" as a reliable source of data. This app may just misinterpret unknown data received from the wheel. Quote Link to comment Share on other sites More sharing options...
RolluS Posted November 2, 2023 Share Posted November 2, 2023 11 hours ago, Seba said: Well, it might be that this "project" firmware has different communication protocol. Also, doesn't rely on Begode app showing "MOS1 error" as a reliable source of data. This app may just misinterpret unknown data received from the wheel. Yes that the case, the app doesn't recognize. The state I was talking about is the bootloader mode: hold lift, power up, hold power click lift. At a moment the board goes in flashing mode, the bluetooth module waits for connection. EUC World connects but the wheel menu stays greeyed out Quote Link to comment Share on other sites More sharing options...
Medhi Baclet Posted December 19, 2023 Share Posted December 19, 2023 On 11/2/2023 at 10:37 PM, RolluS said: Yes that the case, the app doesn't recognize. The state I was talking about is the bootloader mode: hold lift, power up, hold power click lift. At a moment the board goes in flashing mode, the bluetooth module waits for connection. EUC World connects but the wheel menu stays greeyed out Tu peux injecter du code manuellement avec un câble et un pc. Quote Link to comment Share on other sites More sharing options...
84z0r Posted July 6 Share Posted July 6 On 2/17/2023 at 5:46 PM, EMA said: @Freestyleri received a commander firmware too if you need Could you please share it? Quote Link to comment Share on other sites More sharing options...
atdlzpae Posted July 6 Share Posted July 6 1 hour ago, 84z0r said: Could you please share it? I agree, follow your inner Richard Stallman, just dump everything you've got to MegaUpload! I've been dreaming of a "locked wheels" mode in the EUC - it would make it way more stable when leaning against a wall. But I never had the source code to implement it. Quote Link to comment Share on other sites More sharing options...
EMA Posted July 9 Share Posted July 9 On 7/6/2024 at 10:16 AM, 84z0r said: Could you please share it? it's a pcb that need to be plugged into the wheel, similar to the BT module Quote Link to comment Share on other sites More sharing options...
84z0r Posted July 28 Share Posted July 28 On 7/6/2024 at 1:02 PM, atdlzpae said: I agree, follow your inner Richard Stallman, just dump everything you've got to MegaUpload! I've been dreaming of a "locked wheels" mode in the EUC - it would make it way more stable when leaning against a wall. But I never had the source code to implement it. No problem, bro! Here is the Commander HS (C30) firmware: https://mega.nz/file/Wmogia5a#KJFBUwUh7ifs4G-ngPQygmnoSC5g52qhoH0q-CxoS0M Quote Link to comment Share on other sites More sharing options...
alexg Posted August 5 Share Posted August 5 Hi all and @Freestyler personally Is it possible to flash custom firmware to msx 100v black controller? 1 Quote Link to comment Share on other sites More sharing options...
EUCzero Posted August 5 Share Posted August 5 It is possible yes. But if this firmware exists or not I do not know. Use EUCworld to check and install Frestylers firmwares. @Freestyler is no longer active here, so do not expect any answers from him. I hear he had a really bad crash some time ago. I think we should let him be... and just be thankful for all he did for the community. 1 1 Quote Link to comment Share on other sites More sharing options...
Robse Posted August 5 Share Posted August 5 26 minutes ago, EUCzero said: It is possible yes. But if this firmware exists or not I do not know. Use EUCworld to check and install Frestylers firmwares. @Freestyler is no longer active here, so do not expect any answers from him. I hear he had a really bad crash some time ago. I think we should let him be... and just be thankful for all he did for the community. Freestyler had a crash back in Feb 2023, you can read it here approx. 20 pages backward , @Lefteris: it seems you know Freestyler, is there any good news about his condition (which may be shared here)? Quote Link to comment Share on other sites More sharing options...
alexg Posted August 5 Share Posted August 5 3 hours ago, EUCzero said: EUCworld to check and install Frestylers firmwares. No firmware available in the eucworld Quote Link to comment Share on other sites More sharing options...
Lefteris Posted August 5 Share Posted August 5 3 hours ago, Robse said: @Lefteris: it seems you know Freestyler, is there any good news about his condition (which may be shared here)? He recovered but not with ease.. But doesn't want to return to active euc related action .. His decision was to turn a page and forget all about euc.😐😔 1 3 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.