Popular Post Seba Posted June 12, 2021 Popular Post Share Posted June 12, 2021 I'm working on adding some safety features and improving existing safety alarms in EUC World and I need your help. I just need to obtain no-load (free spin) speed of Veteran, Gotway and Begode wheels. How can I help? It's very simple. Just follow these steps: Charge battery to full. This is very important! Speeds obtained for battery charged to less than 100% will give wrong data. Don't follow voltage reading, but wait for your charger LED to go green. If you have regulated charger, make sure it's set to 100%. Turn your wheel on and connect with EUC World. Make sure app bottom bar is green, CSV logging and tour recording is not active. Open app menu and make sure that speed correction in "General" menu is set to 0%. If you have set non-zero speed correction, write original value down and set correction to zero. Carefully lift your wheel up, so it will be able to free spin. Wait for the wheel to automatically shut off and stop rotating. Write down top speed as indicated by EUC World. Close EUC World and turn off your wheel. It's best to repeat steps 2-5 two or even three times to verify results consistency. This way you will determine raw (uncorrected) no-load speed of your wheel for fully charged battery. Now please report this speed by replying in this thread and adding detailed wheel identification data: battery capacity and voltage, wheel model (including wheel version, motor type and firmware version if applicable). If your wheel is a custom version, please add informations about customizations applied. When lifting wheel up be careful! It's best to make this test outside of your home. There is always a risk that you'll put the wheel on the carpet before it stops rotating. It's an easy way to make a rubber marks on the floor or the carpet, and this will probably make your lady very, very angry... 7 Quote Link to comment Share on other sites More sharing options...
Łukasz Posted June 12, 2021 Share Posted June 12, 2021 (edited) Hi, MSP HT C38 / 100V I did three tries - 79.7 km/h each time. I have a changed tire on CST C-803 2.5-14 Best regards Łukasz Więcek Edited June 12, 2021 by Łukasz 1 Quote Link to comment Share on other sites More sharing options...
vladdark Posted June 12, 2021 Share Posted June 12, 2021 Hi,Begode RS HT C38 / 100V second batch 78.2 km/h Green MB CST C-186 2.75-14 TT 2 Quote Link to comment Share on other sites More sharing options...
Tawpie Posted June 12, 2021 Share Posted June 12, 2021 MTen3, 67v 420 WH, "early 2021" (black shell, does have motor cutoff button). No indication of installed FW but I didn't bother getting the Gotway app. 3 trials, all show max free-spin at 24.5 mph (miles, not km... I'm in the colonies) 3 Quote Link to comment Share on other sites More sharing options...
Denny Paul Posted June 12, 2021 Share Posted June 12, 2021 Can I help without an android phone? I’m using DarknessBot of course. 1 Quote Link to comment Share on other sites More sharing options...
fbhb Posted June 13, 2021 Share Posted June 13, 2021 (edited) Veteran Sherman (ordered September and arrived in November 2020): Charge % for test was at 100% = 100.1V: Battery capacity 3200WH: Motherboard version L20-42 (original fitment was L20-34, replaced after charger/control board failure): Firmware version 1.0.56: Free spin test 1. = 100km/h: Free spin test 2. = 99.7km/h: Free spin test 3. 100km/h Edited June 13, 2021 by fbhb 1 Quote Link to comment Share on other sites More sharing options...
..... Posted June 13, 2021 Share Posted June 13, 2021 (edited) Sherman e-wheels 1st version version 1 motor, ver2 (wider) rim. Pirelli angel 80/80/14 tire. Fw 1.0.56 Ambient temp 78F Wheel Temp 99F Battery full 98.9V reported. (it never gets higher so I calibrated eucw for it) 225 total mileage 1* 61.8mph (forwards) 2* 62mph (forwards) 3* 62.1mph (reverse) 99.5kmh -98.8V now- 4* 60.2mph(reverse) Mten3 67v 420ah (newer) Stock firmware (no clue) Battery full @ 66.8V Wheel temp 88F 30 total mileage 1* 23.8mph (forwards) 2* 23.8mph (reverse) 3* 23.8mph (forwards) 38kmh Edited June 13, 2021 by ShanesPlanet 1 Quote Link to comment Share on other sites More sharing options...
Seba Posted June 13, 2021 Author Share Posted June 13, 2021 5 hours ago, Denny Paul said: Can I help without an android phone? I’m using DarknessBot of course. Sure Quote Link to comment Share on other sites More sharing options...
Łukasz Posted June 13, 2021 Share Posted June 13, 2021 7 hours ago, fbhb said: Charge % for test was at 100% = 100.1V Sherman often underestimates the voltage. Most likely you had a full 100.8V My Sherman lowers the voltage by 1V (I checked with a multimeter). Quote Link to comment Share on other sites More sharing options...
Hansolo Posted June 14, 2021 Share Posted June 14, 2021 MS3 84 V MSX 84V EX % batt 100% 100% 100% Speed correction 0% 0% 0% Free speed spin 1 Km/h 71,1 76,2 82,2 Free speed spin 2 Km/h 71,2 76,2 82,7 Free speed spin 3 Km/h 71,5 76,2 82,6 2 Quote Link to comment Share on other sites More sharing options...
RagingGrandpa Posted June 17, 2021 Share Posted June 17, 2021 (edited) Mine below. Gotway seems to increment the BT ID reliably over the years, perhaps it could be a method of inferring "old FW vs new FW"? Quote MTen3 84V 512wh App-reported voltage before Lift: 83.7V Lift 1: 31.7mph power cycle EUC, close app Lift 2: 31.4mph power cycle EUC, close app Lift 3: 31.7mph Tire: original (tubeless) Board sn: 190418403 Usage began: July 2019 EUC World app: manufacturer=LGE brand=lge device=flashlmdd display=QKQ1.191021.002 id=QKQ1.191021.002 model=LM-V500N product=flashlmdd_lao_com sdk=29 instance=a48b850f1f299c91 timeZoneId=America/New_York appVersionName=2.4.1 appVersionCode=2020040001 eucType=GOTWAY eucModel= eucSerial= eucFirmware= eucBluetoothAddress=6C:C3:74:D5:26:20 eucBluetoothName=GotWay_23529 eucSpeedCorrection=0 eucDistCorrection=0 Quote MSX #1 84V 1600wh App-reported voltage before Lift: 83.8V Lift 1: 49.0mph power cycle EUC, close app Lift 2: 48.6mph power cycle EUC, close app Lift 3: 49.1mph Tire: original (H5102) Board sn: 20200808675 Usage began: April 2021 EUC World app: manufacturer=LGE brand=lge device=flashlmdd display=QKQ1.191021.002 id=QKQ1.191021.002 model=LM-V500N product=flashlmdd_lao_com sdk=29 instance=a48b850f1f299c91 timeZoneId=America/New_York appVersionName=2.4.1 appVersionCode=2020040001 eucType=GOTWAY eucModel= eucSerial= eucFirmware= eucBluetoothAddress=88:25:83:F1:6D:0F eucBluetoothName=GotWay_41483 eucSpeedCorrection=0 eucDistCorrection=0 Quote MSX #284V 1600wh App-reported voltage before Lift: 83.8V Lift 1: 47.4mph power cycle EUC, close app Lift 2: 47.4mph power cycle EUC, close app Lift 3: 47.4mph Tire: original (H5102) Board sn: 181115109 Usage began: January 2019 EUC World app: manufacturer=LGE brand=lge device=flashlmdd display=QKQ1.191021.002 id=QKQ1.191021.002 model=LM-V500N product=flashlmdd_lao_com sdk=29 instance=a48b850f1f299c91 timeZoneId=America/New_York appVersionName=2.4.1 appVersionCode=2020040001 eucType=GOTWAY eucModel= eucSerial= eucFirmware= eucBluetoothAddress=88:3F:4A:E5:FD:D2 eucBluetoothName=GotWay_20897 eucSpeedCorrection=0 eucDistCorrection=0 Quote MSP C38 1800wh App-reported voltage before Lift: 100.5V Lift 1: 49.4mph power cycle EUC, close app Lift 2: 49.3mph power cycle EUC, close app Lift 3: 49.3mph Tire: K262 Board sn: 20210427025 (black soldermask) Usage began: May 2021 EUC World app: manufacturer=LGE brand=lge device=flashlmdd display=QKQ1.191021.002 id=QKQ1.191021.002 model=LM-V500N product=flashlmdd_lao_com sdk=29 instance=a48b850f1f299c91 timeZoneId=America/New_York appVersionName=2.4.1 appVersionCode=2020040001 eucType=GOTWAY eucModel= eucSerial= eucFirmware= eucBluetoothAddress=88:25:84:F0:11:3E eucBluetoothName=GotWay_48681 eucSpeedCorrection=0 eucDistCorrection=0 Cheers Edited September 21, 2021 by RagingGrandpa 1 Quote Link to comment Share on other sites More sharing options...
EMA Posted June 17, 2021 Share Posted June 17, 2021 (edited) EXN 95.5 km/h - black board ( c30 100v ) Edited June 19, 2021 by EMA 3 Quote Link to comment Share on other sites More sharing options...
Mark13i Posted June 19, 2021 Share Posted June 19, 2021 (edited) Will it be an available power alarm? - "You have less than 20% of power available - be careful don't accelerate more" MSX v2 - 84V (1600Wh): Test1 - 79.6 km/h Test2 - 80.6 km/h Test3 - 80.0 km/h MCM5 v2 - 67V (310Wh): Test1 - 49.3 km/h Test2 - 48.8 km/h Test3 - 48.5 km/h Edited June 22, 2021 by Mark13i Quote Link to comment Share on other sites More sharing options...
EMA Posted June 19, 2021 Share Posted June 19, 2021 EX 87.3 km/h - green board 100v [ notice that correct speed setting is -8% in app witch result in 80.3 km/h ] 1 Quote Link to comment Share on other sites More sharing options...
Pingouin Posted June 20, 2021 Share Posted June 20, 2021 (edited) Hello, here are some of the results I got :Monster PRO 100V 3600Wh (black motherboard) Test 1 : 106.1 kph Test 2 : 106.2 kph Test 3 : 106.1 kph Monster V3 100V 2460Wh Test 1 : 92.1 kph Test 2 : 91.8 kph Test 3 : 92.3 kph MSP HS 100V 1800Wh Test 1 : 97.1 kph Test 2 : 97kph Test 3 : 97.1kph MCM5 v1 84V 800Wh (need confirmation on this as the owner is not sure if it was at 100% battery, I'll update results) Test 1 : 56.2 Test 2 : 56.3 Test 3 : 56.4 Note : all results are with 0% correction in EUC World. Waiting for EX and Sherman V1 results. Edited June 20, 2021 by Pingouin 2 Quote Link to comment Share on other sites More sharing options...
Tawpie Posted June 22, 2021 Share Posted June 22, 2021 (edited) Never mind, I didn’t read carefully! 😊 Edited June 23, 2021 by Tawpie Quote Link to comment Share on other sites More sharing options...
Hansolo Posted June 22, 2021 Share Posted June 22, 2021 uh, the request for idle speed concerns the BEGODE/GOTWAY and Veteran.... Quote Link to comment Share on other sites More sharing options...
AtlasP Posted June 22, 2021 Share Posted June 22, 2021 1 hour ago, Hansolo said: uh, the request for idle speed concerns the BEGODE/GOTWAY and Veteran.... I'm not the commenter to whom you were responding, but FWIW I think opening up the present topic to all makes/models (emphasizing/keeping the same explicit methodology Seba laid out in the first post) would be an excellent community resource. (With @Seba's permission, of course.) 2 Quote Link to comment Share on other sites More sharing options...
Hansolo Posted June 22, 2021 Share Posted June 22, 2021 It's not going to simplify @Seba 's work if we mix information from other brands... 1 Quote Link to comment Share on other sites More sharing options...
thendless Posted June 22, 2021 Share Posted June 22, 2021 (edited) MCM5 V2 800WH Motherboard Non-Black 20210323 Test 1 : 61.8km/h 83.6V Test 2 : 61.7km/h 83.6V Test 3 : 61.6km/h 83.4V Edited June 22, 2021 by thendless 2 Quote Link to comment Share on other sites More sharing options...
Tawpie Posted June 23, 2021 Share Posted June 23, 2021 18 hours ago, Hansolo said: concerns the BEGODE/GOTWAY and Veteran... Oops got carried away. Apologies to the OP. Quote Link to comment Share on other sites More sharing options...
Flying W Posted June 24, 2021 Share Posted June 24, 2021 RS HT 1st batch with stock tire. 79.7 kph 3 times in a row. Thank you @Seba for all your hard work! 2 Quote Link to comment Share on other sites More sharing options...
Ben Kim Posted June 25, 2021 Share Posted June 25, 2021 (edited) all uncorrected speeds using Darknessbot Veteran Sherman 101.1V firmware 0.0.00 107.5 kmh no load speed Monster Pro 100.2V app reported voltage v2/v3 motherboard 107.7 kmh MCM5 v2 83.2v 63.6 kmh MSX 100V 100.8V 1230Wh 92.2 kmh Edited June 25, 2021 by Ben Kim 1 Quote Link to comment Share on other sites More sharing options...
thendless Posted June 25, 2021 Share Posted June 25, 2021 (edited) 13 hours ago, Ben Kim said: all uncorrected speeds using Darknessbot Veteran Sherman 101.1V firmware 0.0.00 107.5 kmh no load speed Monster Pro 100.2V app reported voltage v2/v3 motherboard 107.7 kmh MCM5 v2 83.2v 63.6 kmh MSX 100V 100.8V 1230Wh 92.2 kmh I noticed on the Denis Hagov's MCM5 V2 video the no load was 64 kmh which lines up with yours. I wonder why mine only tops out at 61.8. The mother board was produced in 20210323 so maybe they made some changes since the earlier V2s? Also interesting given that I don't have the black motherboard. Edited June 25, 2021 by thendless Quote Link to comment Share on other sites More sharing options...
Kalmar Posted June 26, 2021 Share Posted June 26, 2021 (edited) Begode MSX 84V (2500W motor, 1600Wh, motherboard 20201021, Ali) Battery 84V (100%) 1st - 79,7 km/h (84V) 2nd - 79,6 km/h (83,9V) 3rd - 79,4 km/h (83,9V) Edited June 26, 2021 by Kalmar Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.