Search the Community
Showing results for tags 'control board'.
Found 9 results
-
Hi all, I have ordered 14D controller and the battery packs from ewheels. But when I try to install, the motor is not getting engaged. The controller is beeping. Also I checked the motor connection cables several times. Attaching the video regarding the same. Any help is highly appreciated. KS 14D.mp4 Adding another video.... KS 14d_2.mp4 -
Hello everyone, my control Board has died after these circumstances: 1. Rider weighing about 90 kg. 2. Slope upward about 40 degrees. 3. A lot of mud. 4. The v11 went up with the pads (without the pads it would not have been possible to go up as much and maybe nothing would have happened). 5. The legs of the capacitors melted with the consequent cut off. 6. The control board is changed and the motor does not balance. 7. Solution, do a test with the official app and when it asks you about the motor, you have to say that you do want to do a specific test
- 3 replies
-
- 1
-
-
- v11
- control board
- (and 2 more)
-
Hey all, I'm trying to determine if this is an issue with the latest firmware update, a problem with the control board, or another issue entirely. Most recently I have noticed that my Z10's center of balance is making more drastic changes at low speeds. When I start the unit up and begin making small movements, I can feel the sensor reset slightly and at times have had the footplate tilt back and forward a significant amount before slowly resetting. This isn't as extreme as the issue linked in the post below, but is significantly different than when I got the unit. Again it hasn't affected
-
Yet another Ninebot E+ board burnout (I think I'm on 5 or 6), luckily I have a spare control board which I grabbed from an old wheel whose rim fractured Looking at the photos below, can anyone explain what parts may have burnt out here and why? I seem to remember a previous burnout affected the same area on the board. The MOSFETS appear to have been unaffected - there was no lock up of the wheel movement. Interestingly, this control board died at very low speed and when not doing tricks - maybe some solder came loose and caused a short? I'm pretty please how long this board actually las
- 17 replies
-
- 2
-
-
- ninebot e+
- control board
- (and 1 more)
-
A quick poll on control board failures - I would be interested in how common a problem this is.
-
Have recently been bitten by the EUC bug and puchased a Ninebot One E+ couple of months ago. As I'm getting more confident, I am getting bored of the 20kph speed limit I'm getting from the Ninebot One E+ and was thinking if it is possible to swap the control board with this one: https://reseller.alibaba.com/product-detail/16-electric-unicycle-Controller-with-bluetooth_60288223259.html?spm=a2700.7724838.0.0.VsHfbJ Have seen other threads where other users have been swapping their control boards with the one from Microworks purchased from Alibaba. Also wondering if the motor for the ni
-
Does anyone know where i can get control board for ips i130+ electric unicycle? I tried 3 different sites and they saying no
-
Hello EUC community, I've started my EUC journey three month ago with a used e-run 14'' EUC and quickly found out I need something stronger and faster. I bought an IPS ZERO (340Wh) mid of February and got it delivered mid of March. In my third ride it broke - fortunately while I was holding on to a light post. I contacted the seller and after describing the facts, I received the information (full correspondence below): Control board is broken, he will send me a new one. One day later I got an other email stating that an exchange of the control board is not necessary: I shou
-
Hi all, Are there any Ninebot repairs in Canada? My Ninebot E+ circuit/control board sparked, blew a fuse, caught on fire then burnt the circuit board. smoke everywhere...and of course my Ninebot no longer works:( From the photo below, it looks like the Blue & Yellow wire blew up. Anyone have any idea on how to fix this? Lonely broken Nineboter
