Search the Community
Showing results for tags 'change'.
After doing it a few times, i found a way to split it open and remove tyre and tube in about 20minutes. Here goes. NOTE! DO NOT Drop screws down in battery compartment in step 1. 1. Snap of outer skirt, start at the top with the overlying part. Remove batteries (first covers, 2 screws beneath top foam and 2 beneath plastic piece at pedal height...2 snaps and a center pin to remove plastic piece) on both sides. Mark up corresponding battery and BMS CONNECTORS (i use a permanent marker with 1,2,3 aso dots on connecting cables/connectors but it rubs of easy so tape is better) PRESS POWER BUTTON (a few times) WHEN BATTERIES ARE DISCONNECTED TO DISCHARGE CAPACITORS. WHEEL WILL BEEP. WHEN IT DOESN'T BEEP, YOU ARE FINE. NO RESIDUAL VOLTAGE. 2. Remove pedal on non motor cable side (keep other one on for stability) 3. Loosen 3-4 screws for trolley handle on one side and remove all screws holding the alu extender on same side. Remove alu from handle by opening up and move away from pin. Then remove the alu extender Push the" half handle" back down in shell to stay out of the way NOTE!!! If its the first time you split the shell, remove the adhesive tape located right under the control board ( i guess it's there to prevent water from spraying on control board as shell is not very water proof) 4. Remove the screw that was covered by the trolley extender + same screw one opposite side. Screws from here on are LONGER, KEEP THEM SEPARATE (easier to assemble without thinking) 5. Remove four screws on motor cable side holding shell together 6. Remove NON motor cable side screws holding shell to pedal-holders. (crappy construction with fastening so close to each other, look for cracks and drill end of crack with 1-1.5mm drill bit to prevent further cracks. Fill drill hole with i.e. silicone). If wanted make bigger washers or at least replace the super thin non stainless ones with proper washers and screws with hex head) 7. NOW Remove 4 screws holding shell together on other side. 8. Carefully splt shell (lift straight up as control board partially slide into this half) part on non motor cable side and DISCONNECT the connector for that sides LED strip BEFORE removing cover 9. Ready to change tyre or tube 10. I find it easier to use one tyre lever to make first lift and lock it under pedal hanger making sure not to pinch tube when inserting lever (tubes are hard as f... To find and delivery from China 3-4Weeks so go slow) Then using hand to push down tyre to center of rim on opposite side or all around (where rim is deepest), using 2nd lever to bend up enough tyre to be able to lift the rest of by hand....or use another lever to pry tyre off. 3 levers = friend helps, but 2 levers worked for me all times. Then remove tube and the rest is a breeze (other side of tyre bead comes off easy) Change tube tyre or whatever and assemble in reverse order :-) I USE silicone to seal the shell halves back together to make sure water cant reach control board. It requires some slow bending when prying shell halves apart at next disassembly, but to me its worth the 1-2 minutes of slow prying (listening to the silicone crack open) to feel safe(r) in case of water splashes. If you want tape instead (or as well) remove control board after seatimg the two halves together and fixing them with screws. I also added some electric tape on edges of control board to prevent rattle as its quite loosely fitted. Don't forget to loctite screws at pedal hangers and screws holding pedal pins hopefully it helps, most YT videos remove entire shell and control board and DISCONNECT motor cables, totally unnecessary. Waste of time, where you can be riding
Hello, first of all, thank you for the forum. Recently my ninebot segway es1 stopped working, it is necessary to change the "motherboard". The one inside the tube. I can not send it to repair the official service. I have looked at this piece online, I have found it relatively cheap. But I read that if I change the motherboard myself, I will get error 35 and I will not be able to activate it. Somebody could help me ? Thank https://s.click.aliexpress.com/e/YHVNzhI
Hi everyone, We have all read in the media today that UK is clamping down on self balancing devices! Lets try to put a stop to this and show our unity on this matter. Let's try to change the law...!!! l have came a across this petition set up by Steve Miltion. If it gets over 80,000 signatures it will be discussed on the House of Commons! Let's start signing! Please let's spread the word on social media and get the numbers we need! Let's do it for EUC! Thank you for your support #UKridesEUC ---------------------- Allow the usage of self-balancing scooters on public footways and cycle lanes Electric transporters can reduce the number of buses and cars on the streets. Due to the Section 72 of Highway Act 1835, on 12th of October Crown Prosecution Service released a guidance under which the usage of hoverboards and electric unicycles on the public streets would be illegal. Electric unicycles and hoverboards are safe and emission-free transportation devices that have gained popularity in the UK and worldwide since 2012. The devices are portable, they do not require any parking space, and also have restricted speed. Normal riding speed does not exceed running speed. There is a UK manufacturer producing high-quality, stable and safe electric transporters. This company created jobs for over 50 people and represents a significant innovation in transport industry. Click this link to sign the petition: https://petition.parliament.uk/signatures/3689753/verify/jFFUC1F5dv6kEngpgz