Jump to content

EUC Extreme testing available.


EUC Extreme

Recommended Posts

14301160.jpg

Manufacturers and importers! Did you know that you can send me all brands and models of transportation to be tested.
If you want the device to test "a little bit" harder and more thoroughly, I do it :)
Together we can develop even better equipment.
I will give suggestions on how the device could be developed further.
Please contact me via FB or Youtube, and will be discussed in more detail.

Thank you for the picture Yuriy Borodin aka Дед62

Link to comment
Share on other sites

  • 1 month later...
1 hour ago, Sidestreet Reny said:

2 Freeman a4, 1 Freeman a4h, 2 ninebots, 1 Wind Rider, 2 mcm2, 1 generic, 2 Airwheel x2, 1 Airwheel x8 (16), 1 ips zero (didn't kill it,  sold it before I did) and my KS-14b :innocent1:

Whoa @EUC Extreme I never counted my deaths before!

 

Maybe you and @EUC Extreme can join forces and start an 'International EUC Extreme Testing' company. :)

AjsEc5W.jpg

Link to comment
Share on other sites

19 minutes ago, EUC Extreme said:

All have broken down because of power, or power endurance is not enough.
The engine rarely breaks. But the board has a weak point.

 

Yep! Its been mostly the motor for me but the boards have died aswell. Mostly mosfets and cooling issues.

Link to comment
Share on other sites

1 hour ago, EUC Extreme said:

All have broken down because of power, or power endurance is not enough.
The engine rarely breaks. But the board has a weak point.

 

This is the motor getting blown out (crunched, killed, de-gyronated).

 

This is the board frying. (possibly heat that time)

The boards have a weak point for sure but the heat is definitely an issue.

Link to comment
Share on other sites

Just now, Mono said:

Still disappointed. Do you have a candidate for a wheel which you expect to survive longer? 

I don't know. I can't afford to break anymore expensive wheels and the cheap ones can't do all the tricks. You have any ideas?

Link to comment
Share on other sites

15 minutes ago, Sidestreet Reny said:

I don't know. I can't afford to break anymore expensive wheels and the cheap ones can't do all the tricks. You have any ideas?

For the wheels which fry their mosfets you could get a soldering station and a family pack of mosfets - its not too hard to learn how to replace them. @EUC Extremecould also give you some tipps for improving the heat sink.

 

Link to comment
Share on other sites

58 minutes ago, Sidestreet Reny said:

I don't know. I can't afford to break anymore expensive wheels and the cheap ones can't do all the tricks. You have any ideas?

Gotway MCM2/3 and Geekwheel come into my mind, or maybe an InMotion. But I have no idea where to even start how to actually evaluate their reliability, so that isn't of much help. 

Link to comment
Share on other sites

The safest bet is to increase the cooling.
And a simple fuse to prevent the maximum current consumption from rising too high.
Although it would be a really good heat, a momentary spike to kill the printed circuit board.
The mere exchange MOSFET does not help. At the same time always gets damaged more than that.

 

Link to comment
Share on other sites

I wana test them too lol

 I have done almost 1000km on my ks14d and haven't had it a month yet lol

Plus i can test in extreme heat because it gets to 48c here in summer

trying to get 1 of the factorys to sponsor me with a big range fast wheel to get a guinness world record with. hopefully the ks16s

 

Link to comment
Share on other sites

3 hours ago, dalewalker said:

I wana test them too lol

 I have done almost 1000km on my ks14d and haven't had it a month yet lol

Plus i can test in extreme heat because it gets to 48c here in summer

trying to get 1 of the factorys to sponsor me with a big range fast wheel to get a guinness world record with. hopefully the ks16s

 

Where is "here" there's no location info in your profile.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...